Search results

watch?v=WTJ7KszWfz8&list=UUY3LP0b-27eMXmymUX7LxdQ&index=1 FIRST RUN OF MY ENGINE AFTER A 5 YEAR BREAK ON THE BUILD Hi all, My Freestyle has sat in the workshop for around 5 years in a half built state whilst I have been busy with other projects, back on it now, so hope to keep you posted :-)

Hi, Since modifying the front end to take GAZ coil overs I have the following for sale. 1 pair of the Yellow Gas Spax adjustable dampers for sale. These are the rear mini dampers that are used on the front of the kit. They have been off and on the car a few times so there are some marks on...

The old man has got cracking on the diff. Here's a few pics.......... http://i164.photobucket.com/albums/u15/ ... GE_156.jpg http://i164.photobucket.com/albums/u15/ ... GE_157.jpg http://i164.photobucket.com/albums/u15/ ... GE_158.jpg http://i164.photobucket.com/albums/u15/ ... GE_159.jpg...

Guys, Building the dash at the moment and have started thinking about the cowl to fit over the steering column. Due to my hand controls and the way I want it to look I want to mount the ignition switch somewhere else. But is the steering lock a SVA requirement? Speaking to Richard at Donnington...

Simon, Thanks for giving us all a peek at your Coil over conversion for the front of the buggy. Just looking for a suitable set of GAZ shocks on the Rally Design website. Had a very rough measure up of the original mini dampers (new ally sheet nose in the way) and I make them 15" long. So that...

Hi Chaps, In the process of getting an aluminium fuel tank made to fit in the chassis. I am aware that there is some regulation regarding a "restrictor" in the fuel filler neck for unleaded petrol pumps, but thats all I know, can anyone fill me in on what is required so I can get things built...

Hi all, Been out in the workshop staring at the thing! Trying to visualise how best to run the exhaust, is there a max, min height for the exhaust to exit for SVA? I have taken a couple of pics of where it could go, but unsure if Mr SVA man will like it. Any thoughts...

Hi all, Finally working on designing the rear suspension but I need to set the front up properly first. I need to know what height my car will ride at when built. Can anyone measure from the inboard bottom arm bolt to the floor and let me know what height their car sits at. Mine is 217mm from...

Hi Guys, Been giving some thought to the above: Is there a SVA requirement that the rear bulk head (between seats and engine) is at a certain height? I have been considering having mine around 8 inches lower as my lump sits lower and further back. http://s164.photobucket.com/albums/u15/ ...

Hi all, Fitted my master cylinder the other day. Went for a sierra one in the end. I have mounted it on the left side of the pedal box in order to give it more head room and adapted the pedal and shaft so it all lines up. The clutch I will mount on the gear lever as it makes it easier for me to...

Hi everyone, Been toying with where to locate the rad and was wondering if anyone has gone through the trouble of locating it at the front of the Freestyle. The bike radiator is quite compact and I can make more room by removing the battery tray (bike battery to be located at rear) just worried...

Been wondering about wheels of late as well. I was reading the article in which kit mag and Daves wheels are the best ones I have seen ( only in my opinion of course) and wondered what make and size they are. They look like they have an unusual offset for the mini set up and I was wondering if...

Hi all... Got some money burning a hole in the pocket and have been researching seats. I need to work out the postion and mounting of the seats before I hang up the welding mask for a while. Can anyone tell me, do the seats in the Freestyle need to sit up on universal subframes ( that will raise...